behringer/110
110 VCO/VCF/VCA
Legendary Analog VCO/VCF/VCA Module for Eurorack759
Capabilities 3
- Vcfvcf
- Analog low-pass VCF with 20 Hz–20 kHz cutoff frequency range, resonance from off to self-oscillation, and two summed CV mod inputs tracking 1 V/oct.759
- Voltage-Controlled Amplifiervca
- Analog VCA with initial gain control (bias when no CV present), signal level control, two summed CV mod inputs (0–10 V, typically 1 V per 10 dB), and high/low impedance outputs.759
- Voltage-Controlled Oscillatorvco
- Analog VCO with triangle, sawtooth, and pulse waveforms; pitch range controlled by 5-position footage switch (32', 16', 8', 4', 2') and fine pitch knob; pulse width modulation via PW MOD input.759
Jacks 7 — 5 in / 2 out
| Name | Signal | Voltage | Description |
|---|---|---|---|
| Inputs (5) | |||
| MOD IN (VCA) | cv | 0V to 10V | 759 |
| MOD IN (VCF) | cv | 0V to 10V | 759 |
| MOD IN (VCO) | cv | — | 759 |
| PW MOD | cv | 0V to 10V | Accepts a voltage from another module to control the pulse width. When a jack is inserted, the MOD MANUAL control acts as a MOD input level control.759 |
| VCF/VCA SIG IN | audio | — | 759 |
| Outputs (2) | |||
| VCA OUT | audio | — | Sends the VCA signal with either high or low signal levels. High impedance output: +18 dBu max; low impedance output: -2 dBu max. AC coupled.759 |
| VCO OUT | audio | ≤10V | DC-coupled output carrying the VCO signal. Frequency range is <10 Hz to 500 Hz with no external CV, and <1 Hz to 30 kHz using external CV. Max output level 10 V p-p.759 |
Parameters 9
| Name | Type | Range | Behavior |
|---|---|---|---|
| CUTOFF FREQ | fader | 20Hz – 20000Hz | Adjusts the cutoff frequency of the low-pass VCF. May cause VCF oscillation at extreme settings.759 |
| INITIAL GAIN | knob | ≥0 | Adjusts the initial (bias) gain level of the VCA when no control voltage is present. Adjacent LEDs indicate signal (green) and overload (red).759 |
| MOD LEVEL | knob | ≥0 | Adjusts the level of the signal connected to the associated MOD IN jack.759 |
| MOD MANUAL | knob | — | Sets the ratio between the upper and lower portions of the pulse wave (pulse width). When a jack is inserted into PW MOD, this control acts as a MOD input level control.759 |
| PITCH | knob | — | Fine tunes the pitch of the VCO.759 |
| RANGE | switch | — | Sets the pitch range of the VCO in octave steps. Available ranges are 32', 16', 8', 4', 2'.759 |
| RES | knob | ≥0 | Boosts the resonance frequencies selected with the CUTOFF FREQ slider, potentially causing VCF oscillation.759 |
| SIG LEVEL | knob | ≥0 | Adjusts the level of signals connected to the VCF/VCA SIG IN inputs.759 |
| WAVEFORM | switch | — | Selects between triangle, sawtooth, or pulse waveforms for the VCO output.759 |
Firmware history 0 versions
No firmware history recorded.
References 1
-
[759]
Behringer 110 VCO/VCF/VCA Quick Start Guide (mirror of official QSG via device.report)manual● verified 2026-05-22